ult rafast switching rectifiers voltage- 50 to 1000 volts current - 8.0 ampere features ? plastic package has underwriters laboratory flammability classification 94v-o utilizing flame retardant epoxy molding compound. ? exceeds environmental standards of mil-s-19500/228 ? low power loss, high efficiency. ? low forwrd voltge, high current capability ? high surge capacity. ? ultra fast recovery times, high voltage. high temperature soldering : 260 ? o c / 10 seconds at terminals ? pb free product at available : 99% sn above meet rohs environment substance directive request mechanical data ? case: ito-220ac full molded plastic package ? terminals: lead solderable per mil-std-202, method 208 ? polarity: as marked. ? standard packaging: any ? weight: 0.08 ounces, 2.26grams. maximum ratings and electrical characteristics ratings at 25c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% UF800F uf801f uf802f uf803f uf804f uf806f uf808f uf8010f units maximum recurrent peak reverse v oltage 50 100 200 300 400 600 800 1000 v maximum rms voltage 35 70 140 210 280 420 560 700 v maxi mum dc bl ocking voltage 50 100 200 300 400 600 800 1000 v maximum average forward rectif ied current at tc=100c 8.0 a peak forward surge current , 8.3 ms single half sine- wave super imposed on rated load (j edec method) 125 a maximum instantaneous forward vol tage at 8.0a per element 1.0 1.30 1.50 1.70 v maxi mum dc reverse cur rent (note 1) ta=25c at rated dc blocking voltage ta=125c 10 500 a typical junction capacitance (note 1) 80 50 pf maximum reverse recovery time (note 2) 50 75 ns typical thermal resistance note r jc 15 operating and storage temperature range t j -55 to +150 notes: 1. measured at 1 mhz and applied reverse voltage of 4.0 vdc. 2. reverse recovery test conditions: i f =.5a, i r =1a, irr=.25a. 3. thermal resistance from junction to ambient and from junction to lead 0.375? (9.5mm) p.c.b mounted. ito-220ac unit:inch(mm) .161(4.1) max .130(3.3) max .185(4.8) max .272(6.9) .248(6.3) .055(1.4) max .035(0.9) max .100(2.55) .543(13.8) .512(13.0 ) .1 00(2.55) .114(2. 9 ) .098(2.5) .032(0.8) max .606(15.4) .583(14.8) .112(2.85) .100(2.55) .406(10.3)max .1 34(3.4)dia .113(3.0)dia data sheet UF800F~uf8010f semiconductor http://www.yeashin.com 1 rev.02 20110725 c c/w
ratingand characteristiccurves (+) 25vdc (approx) (-) oscillosccope note 1 1.rise time=7ns max input impedance=1 megohm. 22pf 2. rise time=10ns max. source impedance = 50 ohms 1 non inductive 50 noninductive 10 noninductive pulse generator note 2 (-) (+) +0.5a 0 -0.25 -1.0 set time base for10ns/cm 1cm t rr fig. 2- forward characteristics number o f cycles at 60hz fig.4-peak forward surge current serepma,tnerrucegrusdrawrof fig.3-forward currentderating curve 80 40 20 1 10 100 notes: fig.1-reverserecovery time characteristic and test circuitdiagram 10 1 0.1 0.01 .4 .6 .8 1.0 1.2 1.6 1.8 cdrawrofsuoenatsni )a(,tnerru forward voltage , volts 60 t=25 c j o 140 100 120 1.4 akaelesrever-ri tnerruceg serepmaorcim. %o f piv. volts fig.5- typical reverse characteristics 1000 100 1.0 20 40 60 80 100 120 t = 25 c j o t = 125 c j o 140 0.1 egareva rof tnerrucdraw case temperature, c o 0 50 100 150 12.5 10.0 7.5 5.0 2.5 0 100 2.0 10 ,ecnaticapac fp fig.6-typical junction capacitance reverse voltage,volts 1 2 5 10 20 50 100 200 160 120 80 240 40 0 200 500 t = 25 c j o 600-800v 300-400v 50-200v UF800F~uf8010f http://www.yeashin.com 2 rev.02 20110725
|